描述:
ethtool是用於查詢及設定網絡卡引數的命令。
概要:
ethtool ethx //查詢ethx網口基本設定
ethtool –h //顯示ethtool的命令幫助(help)
ethtool –i ethx //查詢ethx網口的相關資訊
ethtool –d ethx //查詢ethx網口註冊性資訊
ethtool –r ethx //重置ethx網口到自適應模式
ethtool –s ethx //查詢ethx網口收發包統計
ethtool –s ethx [speed 10|100|1000]\ //設定網口速率10/100/1000m
[duplex half|full]\ //設定網口半/全雙工
[autoneg on|off]\ //設定網口是否自協商
[port tp|aui|bnc|mii]\ //設定網口型別
[phyad n]\
[xcvr internal|exteral]\
[wol p|u|m|b|a|g|s|d...]\
[sopass xx:yy:zz:aa:bb:cc]\
[msglvl n]
舉例:
1)[root@linux /]# ethtool eth1
settings for eth0:
2)[root@linux /]#ethtool -i eth1
driver: bnx2
version: 2.0.8-rh
firmware-version: 6.2.12 bc 5.2.3 ncsi 2.0.11
bus-info: 0000:01:00.0
3)[root@linux /]# ethtool -s eth1
nic statistics:
rx_bytes: 216494818
rx_error_bytes: 0
tx_bytes: 27084170553
tx_error_bytes: 0
rx_ucast_packets: 2933822
rx_mcast_packets: 33
rx_bcast_packets: 956
tx_ucast_packets: 18464909
tx_mcast_packets: 6
tx_bcast_packets: 179
tx_mac_errors: 0
tx_carrier_errors: 0
rx_crc_errors: 0
rx_align_errors: 0
tx_single_collisions: 0
tx_multi_collisions: 0
tx_deferred: 0
tx_excess_collisions: 0
tx_late_collisions: 0
tx_total_collisions: 0
rx_fragments: 0
rx_jabbers: 0
rx_undersize_packets: 0
rx_oversize_packets: 0
rx_64_byte_packets: 959
rx_65_to_127_byte_packets: 2930241
rx_128_to_255_byte_packets: 2634
rx_256_to_511_byte_packets: 752
rx_512_to_1023_byte_packets: 169
rx_1024_to_1522_byte_packets: 56
rx_1523_to_9022_byte_packets: 0
tx_64_byte_packets: 183
tx_65_to_127_byte_packets: 357
tx_128_to_255_byte_packets: 750
tx_256_to_511_byte_packets: 224
tx_512_to_1023_byte_packets: 991032
tx_1024_to_1522_byte_packets: 17472548
tx_1523_to_9022_byte_packets: 0
rx_xon_frames: 0
rx_xoff_frames: 0
tx_xon_frames: 0
tx_xoff_frames: 0
rx_mac_ctrl_frames: 0
rx_filtered_packets: 0
rx_ftq_discards: 0
rx_discards: 0
rx_fw_discards: 0
4)[root@linux /]# ethtool -s eth1 autoneg off speed 100 duplex full
相關:
1)[root@linux /]# which ethtool
/sbin/ethtool
2)[root@linux /]# rpm -qf /sbin/ethtool
ethtool-1.6-5
3)怎樣使ethtool設定永久儲存在網路裝置中?
解決方法一:
ethtool設定可通過/etc/sysconfig/network-scripts/ifcfg-ethx檔案儲存,從而在裝置下次啟動時啟用選項。
例如:ethtool -s eth0 speed 100 duplex full autoneg off
此指令將eth0裝置設定為全雙工自適應,速度為100mbs。若要eth0啟動時設定這些引數, 修改檔案/etc/sysconfig/network-scripts/ifcfg-eth0 ,新增如下一行:
ethtool_opts="speed 100 duplex full autoneg off"
解決方法二:
將ethtool設定寫入/etc/rc.d/rc.local之中。
二解決方法:
對intel千兆網絡卡禁用自適應時必須指定鏈路速度和全雙工模式。當使用ethtool來禁用使用e1000網絡卡驅動模組的網絡卡自適應特性時,必須同時指定鏈路速度和全雙工工作模式。例如: ethtool -s eth0 autoneg off
會邊比自適應,但是只是臨時禁用,如果在命令中沒有指定鏈路速度和全雙工工作模式,驅動會自動重新開啟自適應。
為了使用ethtool工具來禁用e1000網絡卡驅動模組的網絡卡自適應特性,使用以下步驟
1. 進入終端模式。 2. 以root身份執行 ethtool -s ethx autoneg off speed 1000 duplex full
這裡ethx是網絡卡的名字(例如eth0或者eth1等等),這個命令將關閉該網絡卡的自適應特性,並且強制設定網絡卡速度為1gb,全雙公模式。
另外ethtool比mii-tool要高階,mii-tool只支援 port: mii的網絡卡.
ethtool 命令詳解
命令描述 ethtool 是用於查詢及設定網絡卡引數的命令。使用概要 ethtool ethx 查詢ethx網口基本設定,其中 x 是對應網絡卡的編號,如eth0 eth1等等 ethtool h 顯示ethtool的命令幫助 help ethtool i ethx 查詢ethx網口的相關資訊 et...
ethtool 命令詳解
ethtool 是用於查詢及設定網絡卡引數的命令。使用概要 ethtool enp5s0fx 查詢ethx網口基本設定,其中 x 是對應網絡卡的編號,如enp5s0fx 等等 ethtool h 顯示ethtool的命令幫助 help ethtool i enp5s0fx 查詢ethx網口的相關資訊...
用ethtool 命令解決Linux 網絡卡丟包
生產中有一台linux裝置併發比較大,droped包比較多,尤其是在跑遊戲資料報的時候,存在嚴重的丟包現象,懷疑網絡卡效能不足,在更換裝置前想能不有通過軟體方法解決,通過網上一些資料顯示,出現這種現象,也有可能是網絡卡buffer size 太小的原因,遂嘗試更改buffer 大小解決,下面的裝置執...